Here's why I can't work on my room divider!
That's down about 1/2 of what we had gotten yesterday.
Still may not be warm enough today to get rid of the rest of it. Definitely not warm enough for painting. Got an auction to go to tomorrow, then maybe Sunday I can get back to gluing and painting.
Friday, April 9, 2010
Monday, April 5, 2010
Easter 2010
Here's a collage of Blake and Jayden putting stickers on plastic eggs for the Egg Hunt.
How'd that get in there?
Collage of Jayden looking for her Easter basket
Our dinner table and Easter cake
Now that Easter is over, I can get back to my project.
Tuesday, March 30, 2010
Photo Room Divider Tutorial - Step 5
Tools for this step:
Hack Saw
Carpenter Square
Tape measure
Welder (We used a stick welder)
Grinder
Materials for this step:
3/8" hollow rod ( we got a 3' piece, but you'll only need less than 1/2 of it)
5 - 5/16" Square U-Bolts
Welding Rods
We're almost finished with the construction!
A hack saw works better for the cutting in this step, since the pieces are so small and not very difficult to cut by hand. Theoretically, you could the whole project with a hack saw, if you don't have a chop saw, but it will take a lot longer and take a lot more effort. So, cut the u-bolts in half so you have 2 identical pieces of each. Next, cut off the threads. If you have need for 1 1/2" threaded rod, keep the pieces, otherwise, toss them.We needed 9 hinges, so there is 1 half bolt left with threads on. This could be used as a "bolt in" bracket if there is ever a need. You'll end up with 2 L shaped rods from each bolt. Cut the hollow rod into 9 pieces about 1/4" longer than the long side of the L shaped rod. Save the rest
of the rod for another project. These 2 pieces make
up one complete hinge.
Weld the rod ends of the hinge into place along one side of each panel. Keep the rod side on the same side of each panel so, you don't end up with 2 rods together and 2 pins together. Next, stand up the panels and place the pin in the rod; then clamp under the pin to hold it in position and weld it in place.
So, here's a picture of what the hinges look like. You won't see the whole project until I have it painted, which is the final step. There is a surprise touch that I've
added that I hope you like.
Sunday, March 28, 2010
Photo Room Divider Tutorial - Step 4
Tools for this step:
Chop Saw
Carpenter Square
Tape measure
Welder (We used a stick welder)
Grinder
Materials for this step:
3/8" metal rod
Per section for this step:
Various sizes (you have to measure)
Welding Rods
Plywood Sheet from step1
Scrap pieces of board from step 1
We're getting closer....
Now that all the frames are welded in, measure for the remaining vertical pieces between the frames, the top of section to top of frames and the bottom of section to bottom of frames. Cut these pieces and weld in place.
We used a scrap piece of board top
make a template, cut to the width of
half of one of the spaces. Be sure to
always use the spacer on the same
side to keep the spacing consistent,
top to bottom.
Repeat for he remaining sections.
This is what we have so far. We didn't get to the hinges today, but hopefully tomorrow we will figure those out.
I know this seems like it is taking a
long time, but we have to work
around our daily full time work.
Saturday, March 27, 2010
Another Blog
I moved the Feats and Accomplishments page to it's own blog. I didn't like that you can't post to a specific page, only the home page. I felt each item should have it's own posting/page. I may do that with the plans page, which is still under construction anyway, in the future too.
Here's the URL:http://tru-featsandaccomplishments.blogspot.com/
Here's the URL:http://tru-featsandaccomplishments.blogspot.com/
Wednesday, March 24, 2010
Photo Room Divider Tutorial - Step 3
Tools for this step:
Chop Saw
Carpenter Square
Tape measure
Welder (We used a stick welder)
Grinder
Materials for this step:
3/8" metal rod
Per section for this step:
48 - approx. 4" pieces (You will have to measure to be exact)
Welding Rods
Plywood Sheet from step1
Scrap pieces of board from step 1
Continuing on
Cut a template to the size of your photos with a piece of scrap board. Ours is 4X6. Use this to place between the vertical rods where you want your frames situated.
The vertical rods should all be equal at 4" apart, so you can cut pieces of rod to this length and weld them in place.
Picture of 4" pieces of rod. I did grind some on the edges just to take off some of the burrs.
The welding in progress.
Ours have the outside 2 sections mirror images of each other and the inside 2 sections are identical.
Here ends step 3. That was a lot of putsy work
wasn't it. It actually doesn't look so bad the way it is, but we don't want any grandkids getting their heads caught, so we'll be adding rods in between.
wasn't it. It actually doesn't look so bad the way it is, but we don't want any grandkids getting their heads caught, so we'll be adding rods in between.
Next Step, finishing up the vertical rods and hinges.
Sunday, March 21, 2010
Photo Room Divider Tutorial - Step 2
Tools for this step:
Chop Saw
Carpenter Square
Tape measure
Welder (We used a stick welder)
Power miter saw
Materials for this step:
3/8" metal rod
Per section for this step:
4 - approx. 52" (You will have to measure to be exact)
Welding Rods
Plywood Sheet from step1Scrap pieces of board from step 1
Let's continue.
Place one section on the plywood sheet on a flat surface. Measure between the upper cross bar and the bottom and cut 4 rods to that length, as long as you measured across and the measurements are the same.
Place these pieces approx. 4" apart in the inside
of the section. They will be 2 1/2" or closer to the edges.
I designed this for 4X6 pictures, so,if you want different sizes, you'll have to adjust your measurements.
Use 2 scrap pieces of board cut to 4" to make sure all the inside rods are evenly spaced. Start with the center
Place one section on the plywood sheet on a flat surface. Measure between the upper cross bar and the bottom and cut 4 rods to that length, as long as you measured across and the measurements are the same.
Place these pieces approx. 4" apart in the inside
of the section. They will be 2 1/2" or closer to the edges.
I designed this for 4X6 pictures, so,if you want different sizes, you'll have to adjust your measurements.
Use 2 scrap pieces of board cut to 4" to make sure all the inside rods are evenly spaced. Start with the center
space.
Weld in place. Repeat for the remaining sections.
Weld in place. Repeat for the remaining sections.
It's coming along nicely. We got a lot done in this step.
Next step, even more cutting and welding.
A lot of putsy stuff!
Subscribe to:
Posts (Atom)








