Saturday, March 20, 2010

Photo Room Divider Tutorial - Step 1

Tools for this step:
Carpenter square        Tape measure                      
                                                                                  
   
Chop Saw
 
Adjustable Clamp            Welder                           
 
Wheel Rim                                             Drill  

    
  
Materials for this step:
3/8" metal rod (We used approx. 48' per section total)
        Per section for this step:
1 - 12'
2 - 19"
Welding Rods
4X8 sheet of plywood (This can be an old used piece)
6 - 2X6  pieces of lumber (each 12" -18" long, again, this can be scrap)
2" Screws


Let's begin.

Make 4 of these sections, or as many as you want
your room divider to be wide. Ours are each
approximately 19" wide by 5' 4" tall, so 4 are about
6' 4" wide.

This step takes two people. Mark the center of the
12' piece of 3/8" rod. Place the mark at the top of
the wheel rim and clamp it at that point. Now, while one person stands on the rim to keep it from moving, the other person bends the rod around the rim until the
sides are parallel. Be sure to OVER BEND, because
it will go out some when you let go. Remove the clamp  from the rod and place on a sheet of plywood.
Excuse the dirty clothes. We do not work in dress clothes.



Now you will make a jig or frame so that all your pieces
are uniform. Make sure you use the section with the
shortest side, because that will determine the height of
your room divider.
To do this, we started by screwing a 2X6 board square
to the top of the sheet of plywood. Bring the curved rod
to the bottom of this board and start working down one
side of the rod, screwing a board square to the side of
the plywood sheet.
A plywood sheet should have manufactured sides, so it
should be square. Do one more board on that side, then
move over to the other side, making your boards square
to the top board. Make sure the top boards are the same
distance apart as the bottom boards.  Finally screw the
last board across the bottom, in line with the bottom of the
shortest side of the rod. Make sure this board is square to
both the bottom side boards.


Next, measure the space just below where the rod starts to go straight and cut a piece of rod to fit between. Mark this place with a marker right on the plywood, square to the sides. If you've squared it up right, the space at the bottom should be the same.
Put the top rod in at your mark and weld. Put the bottom rod in up against the bottom board and weld. After the welding has cooled, cut off any overhang on the chop saw.



Here's a pic of my line on the plywood. In all subsequent sections, the top of the rod will be placed at the bottom of the line. This will make all the sections very close to the same.









So, this is what we have done so far. They look pretty  
even. The last one is on a different board, so it looks lower. We are well pleased with our project so far,

That's enough for step 1. The next step will be a lot of
cutting and welding.

Update on Room Divider

Got the rods last night. Delivered right to our yard. How's that for service. He dropped them off on his way home. So, hopefully today we are going to start the process and I will get a tutorial on here as I have time.

Tuesday, March 16, 2010

Room Divider - Final design........hopefully!


So, this looks like what we're going with. Just have to wait for the metal shop guy to get the rods.

Monday, March 8, 2010

Another Room Divider

So, how about this one? Are you lovin' it? Maybe smaller rectangles on the top. This is what I have in mind for the pics on one side. No......... they won't all be Steph and Jason! This is just my working prototype.

Thursday, March 4, 2010

I'm Back!




Now that I have faster internet, I'm going to try the blog thing again.
First up:
I plan to have the local metal worker make me a room screen and am looking for opinions.
Which design do you think would look best with old style pics?


#1

Friday, December 31, 2004

More Fire In Shallowville

Last night Uncle Bill's shed burned. Not to the ground, but quite a lot of damage. I did not witness it, because I was abed already, and given my excitement of a few weeks ago, Gary didn't tell me til morning. Anyway, he has quite a mess to clean up. Water system to get repaired, so the cattle have water etc... Then there's the insurance to deal with. You know how they try not to pay. I'm afraid they'll say no way because he had an electric heater going to keep the water system from freezing. That's the area where it started by the way.



Again I say Thank You God, nobody got hurt and things can be replaced. It does put my fire in perspective though. We may have lost an old truck, but not nothing expensive to replace or fix.



Well, that's about all I know. If you want more info, you'll have to talk to Gary or Al.



Have a Happy New Year, and let's hope this next year is better than the last!

Wednesday, December 8, 2004

What's Cookin' ?

The GMC to be specific!



Yesterday when I was hauling a wagon of grain into the feedmill, I saw smoke coming from by the hind tire. I thought maybe a tire was rubbing or something, so I slowed down to pull over. About this same moment, I was meeting a car on the road and the driver started gesturing to me. I flicked my lights on and off trying to get Al's attention, ( he was ahead of me in the tractor with wagon), to no avail. I found out later he did not see the lights, but noticed I was slowing down. Apparently the headlights were gone already by that time.



Well, I stopped and got out to investigate. Sure enough, there was smoke coming out the back, but it was originating in the front. I got away from the truck and tried calling Al several times, but he said his phone did not ring! I was finally leaving a message, when all of a sudden the truck began to try to start by itself! At that point while I was telling Al what happened, I told him I was calling 911 and getting outta there.



By this time I was in a plowed field and tried to run around to the back of the truck where a women had stopped to see if I needed assistance. Have you ever tried to run in a plowed field, with snowpants and boots on I might add? Not easy! Anyway, I got through to the 911 dispatcher and she got the info and dispatched the fire dept and a deputy. According to the time log on my phone it was a little over nine minutes til when I could see the fire truck and hang up with the dispatcher.



In the meantime some guys had stopped in the front of the truck and were going to it with a fire extinguisher. I told the dispatcher about this and she said to wave them away, which I did and they backed off. A couple of minutes later someone else was going to the truck with the fire extinguisher and I tried to wave them off as well, but he wouldn't go without trying first. Guess who the JACKASS was? It was AL!!! At this point I started losing it somewhat, because here is my son trying to put out a vehicle fire, that I was afraid could explode at any moment. I finally yelled loud enough that the fire dept was on it's way and he backed off. I was very relieved then and glad there was someone there keeping me company. It helped to keep me mostly grounded. Turns out this woman's son was one the volunteer fireman who responded.



Ok, so they finally got the fire out, and mostly all I could think of was " There goes my purse and everything in it" If not burnt up, then destroyed by the water or whatever they were spraying in the truck. Then the deputy came and got some info and I finally got to go to the truck. First thing I did was get my purse which was wet and stinky, but intact, which is more than I can say for the GEMS. It was destroyed in the front. And guess what? Being that it was an older truck we had taken the comprehensive insurance off and had only liability, so it is a total loss to us, but the insurance will pay for the fire call, so far, but you know insurance companies, if they can get away without paying they will.



Obviously I or no one else was hurt or I wouldn't be writing this. During my drive before this happened, I was thinking about blowing a tire or something and praying a little, and jokingly said to myself, " May the Force be with me" ( God in my case, not the Star Wars Force, Jason, but you did come to mind). So, I guess He was with me as all that was lost was a truck.



Thank-You GOD!



So that's my story. And this just after I was telling Jessica online that nothing was new here. Once in awhile, I guess we do get some excitement in our lives, thankfully it is rare. I will take my dull boring life over this anytime.

Related Posts with Thumbnails